WF 3154 – Fault Injection Module
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel has a capacity to handle signals up to 58V/2.5A and provides three solid state relays that can be used to create electrical fault conditions like:
• Open circuit
• Short circuit to battery
• Short circuit to ground
It is possible to connect channels in parallel for increased current capability.
$ 649.00
In stock
Quote request for WF 3154 – Fault Injection Module
Downloads, Information & Videos
Downloads
LabVIEW Driver
AC0022-003 Container – VIP file.zip | Older versions of this driver might be found HERE
User Manual
AC0022-002 WF3154 User Manual.pdf
Data sheet
AB0005-005 WF 3154 Data Sheet.pdf
Additional Downloads
Mixing WF and NI modules
AB0005-056 AN4 Mixing WF and NI modules.pdf
WF modules and Scan mode
AB0005-041 AN13 WF modules and Scan mode.pdf
FPGA Resource Usage for WF C Series modules
AB0005-104 AN16 FPGA Resource Usage for WF C Series modules.pdf
Integrating WF modules with NI VeriStand
AB0005-098 AN14 Integrating WF modules with NI VeriStand.pdf | Code examples can be downloaded HERE
Specification
– Channels; 4
– Max Voltage; 58 V
– Max current; 2.5A/ch (6A peak < 100ms)
– Ch. resistance; < 0.1 Ohm
– Max power dissipation; 1.5W/module
– Max Voltage; 58 V
– Max current; 2.5A/ch (6A peak < 100ms)
– Ch. resistance; < 0.1 Ohm
– Max power dissipation; 1.5W/module
Features
– Four independent, galvanically isolated channels
– Entirely solid-state design
– Two general purpose short circuit rails.
– LabVIEW driver included
– Compatible with NI VeriStand
– Entirely solid-state design
– Two general purpose short circuit rails.
– LabVIEW driver included
– Compatible with NI VeriStand
Application areas
– Product safety testing
– HiL testing (Hardware in the Loop)
– FMEA tests
– Fault simulation
– HiL testing (Hardware in the Loop)
– FMEA tests
– Fault simulation
General information
– Product Net Weight: 0.17 kg
– Country of Origin: Sweden (SE)
– Harmonized System (HS) / TARIC Code: 8537109199
– Country of Origin: Sweden (SE)
– Harmonized System (HS) / TARIC Code: 8537109199
FAQ: What kind of connector are used for the module?
A: The WF 3154 uses a 10-Pos Plug. You should connect a terminal block for 10-Pos Plug to the module. This terminal block is included together with the module when shipped from WireFlow.
FAQ: How many FPGA resources does a C series module consume?
A: The FPGA usage of a specific software and hardware combination is affected by multiple factors such as; FPGA type and size, compilation options, the random starting point for FPGA code placement etc.
Hence, it is impossible to derive an exact figure that defines the FPGA usage of a specific C series module. For customers that are uncertain on whether their application will fit on a specific FPGA with a WireFlow C series module it is recommended to make a test-build. Note that no hardware is needed to make a test build.
For more details, please see AB0005-104 AN16 FPGA Resource Usage for WF C Series modules.
Hence, it is impossible to derive an exact figure that defines the FPGA usage of a specific C series module. For customers that are uncertain on whether their application will fit on a specific FPGA with a WireFlow C series module it is recommended to make a test-build. Note that no hardware is needed to make a test build.
For more details, please see AB0005-104 AN16 FPGA Resource Usage for WF C Series modules.
FAQ: Does the module work with cDAQ-systems from National Instrument?
A: No. The module is only compatible with the CompactRIO chassis, including the expansions chassis for Ethernet, EtherCAT, R Series and MXI-Express. However, National Instruments has released a CompactRIO series that supports NI-DAQmx, called NI-904x (you can find them HERE). On these chassis you can use all of our C Series modules.
FAQ: Is the WF 3154 module compatible with cDAQ-systems from National Instrument?
A: No it is not. At the moment only the WF 3132 module works on both CompactDAQ and CompactRIO systems. The WF 3154 is for the time being only compatible with the CompactRIO systems, including the expansions chassis for Ethernet, EtherCAT, R Series and MXI-Express. However, National Instruments has released a CompactRIO series that supports NI-DAQmx, called NI-904x (you can find them HERE). On these chassis you can use all of our C Series modules.
ECU test demo
NI Alliance Partner, WireFlow AB, shows a demo that illustrates how a simple Electronic Control.