WF 3154 – Fault Injection Module

The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel has a capacity to handle signals up to 58V/2.5A and provides three solid state relays that can be used to create electrical fault conditions like:

• Open circuit
• Short circuit to battery
• Short circuit to ground

It is possible to connect channels in parallel for increased current capability.

$ 935.00

In stock

Product Code: AE0002 Category: Tag:

Quote request for WF 3154 – Fault Injection Module

Downloads, Information & Videos


LabVIEW Driver

AC0022-003 Container – VIP | Older versions of this driver might be found HERE

User Manual

AC0022-002 WF3154 User Manual.pdf

Data sheet

AB0005-005 WF 3154 Data Sheet.pdf

Additional Downloads

Mixing WF and NI modules

AB0005-056 AN4 Mixing WF and NI modules.pdf

WF modules and Scan mode

AB0005-041 AN13 WF modules and Scan mode.pdf

FPGA Resource Usage for WF C Series modules

AB0005-104 AN16 FPGA Resource Usage for WF C Series modules.pdf

Integrating WF modules with NI VeriStand

AB0005-098 AN14 Integrating WF modules with NI VeriStand.pdf | Code examples can be downloaded HERE


–  Channels; 4
–  Max Voltage; 58 V
–  Max current; 2.5A/ch (6A peak < 100ms)
–  Ch. resistance; < 0.1 Ohm
–  Max power dissipation; 1.5W/module


–  Four independent, galvanically isolated channels
–  Entirely solid-state design
–  Two general purpose short circuit rails.
–  LabVIEW driver included
–  Compatible with NI VeriStand

Application areas

–  Product safety testing
–  HiL testing (Hardware in the Loop)
–  FMEA tests
–  Fault simulation

Shipping information

– Product Net Weight: 0.17 kg
– Country of Origin: Sweden (SE)
– Harmonized System (HS) / TARIC Code: 8537109199

Support & FAQ

Visit our knowledge base on our Support Portal if you don’t find any answers to your questions here.

General information

Can I use ScanEngine for the module?
ScanEngine access is not directly accessible for Third-Party modules, but it is quite easy to mix WireFlow C Series modules with other NI modules in a system and still access the NI modules in Scan Mode. Please see application note AB0005-056 AN4 Mixing WF and NI modules for a step-by-step guide how to do this.

What kind of connector are used for the module?
The WF 3154 and uses a 10-Pos Plug. You should connect a terminal block for 10-Pos Plug to the module. This terminal block is included together with the module when shipped from WireFlow.

Is the WF 3154 module compatible with cDAQ-systems from National Instrument?
No it is not. At the moment only the WF 3132 module works on both CompactDAQ and CompactRIO systems. The WF 3154 is for time being only compatible with the CompactRIO systems, including the expansions chassis for Ethernet, EtherCAT, R Series and MXI-Express. However, National Instruments has released a CompactRIO series that supports NI-DAQmx, called NI-904x (you can find them HERE). On these chassis you can use all of our C Series modules.

How many FPGA resources does a C series module consume?
The FPGA usage of a specific software and hardware combination is affected by multiple factors such as; FPGA type and size, compilation options, the random starting point for FPGA code placement etc.
Hence, it is impossible to derive an exact figure that defines the FPGA usage of a specific C series module. For customers that are uncertain on whether their application will fit on a specific FPGA with a WireFlow C series module it is recommended to make a test-build. Note that no hardware is needed to make a test build. For more details, please see AB0005-104 AN16 FPGA Resource Usage for WF C Series modules.

ECU test demo

NI Alliance Partner, WireFlow AB, shows a demo that illustrates how a simple Electronic Control.